Pages

Tampilkan postingan dengan label for. Tampilkan semua postingan
Tampilkan postingan dengan label for. Tampilkan semua postingan

Kamis, 12 Januari 2017

False battens blocking for deck framing and shiny stuff

Trying to push this project on toward completion, tonight I started measuring for the deck framing. So far, it has been mercifully simple.

I clamped my big adjustable T-Square onto the forward frame at the centerline, and measured the halfway point between the frame and the breasthook. Then, I set my 48" ruler across that halfway point, at right angles to the T-Square. After determining the rulers contact point with the sheer was an equal distance from the frame on both sides, I clamped the ruler into place, and marked the sheers. Then, I measured the angle at the intersection of the ruler and the sheer. Thankfully, it was a very easy-to-cut 20°. 

Measuring for the deck framing.

The blocking for the deck framing required a simple 20° cut. Here is the starboard side being epoxied into place.

Blocking for the deck framing on the port side.

Here, the false battens on the floor are being epoxied into place. All those boards look a little excessive to my eye, but the false battens do serve a practical purpose.

Tonight I drilled the holes & installed the stainless steel grab handle on the forward frame. The first time I rode in a Glen-L Utility, I realized this is a "must-have" item.

Progress...

Read More..

Jumat, 04 November 2016

Grinding your Own

 A year ago or so we ran out of coffee while camping and while in town, picked up some more coffee.  I checked the bag that the coffee was in and it felt pre-ground.  Next morning when we got up to make coffee, the beans turned out not to be ground.  Luckily, there was a large rock at the edge of the campground and the banks of the river across the street yielded a mano, the stone you hold in your hands to grind the corn. With a little practice we managed to make a fine grind and breakfast was saved.
Closeup on the grinding operation.


 Of course, grinding stuff on stone grinders is nothing new.  It is in fact quite old and just recently, we visited Montezumas Castle in Arizona where a number of stone grinders were on exhibit.
 

 The stone grinders in the American Southwest are known as Mano and Metate, the metate being the large flat stone and the smaller one you grind with is called the Mano.
 A slightly different arrangement visible throughout California are large flat boulders that were used for grinding acorns, a staple food in much of California before the arrival of the Europeans.  Unlike the metate which is flat, the grind stones for acorns have conical pits in them.  This prevents the acorns from spreading about.  Any that escape in the grinding process can be easily swept back into the hole.
And here is a long view of the grinding rock.  Note that the rock had a number of pits in it and so had room for a number of women to go about their grinding in a sociable way.  The rock also happens to be conveniently located in a flat area surrounded by oaks.
Read More..

Rabu, 26 Oktober 2016

The Utility Preparing for Planking



A fellow boatbuilder pointed out to me that if I cover the transom first, before planking the sides and bottom of the boat, then the end grain of my planking is going to show around the rim of the transom. (Thanks Chris!) Of course, this only poses an issue if you plan on bright-finishing your transom, which is exactly what I’m planning to do. I’m planning to paint the rest of the hull. So, paint will cover the end grain of the transom as viewed from the side.

So now, my plan has changed to planking the sides and bottom of the boat first. The first pieces of planking that go on will be short 4’ aft sections on the sides. I will be butt-joining these pieces to longer 8’ pieces that will plank the forward sections on the sides. This will allow the butt joint to be located in the flatter aft section of the boat, which means it will be easier to do, and there will be less stress on the joint. I have to join the planking in sections like this, because plywood comes in standard 8’ lengths, and my boat is 11’ long.

In preparation for planking these aft sections, I’ve been sanding away dried runs of epoxy, etc from those parts of the boat I can’t easily get to once the planking is on. I’ve also worked to clean up the shape of the seat riser cutouts in frame #1. Still, before I can plank this aft section, I need to encapsulate these frame cutouts, as well as a couple of other places I won’t be able to reach once the planking is on.

Then, God willing, I should be able to begin planking the little boat.


Dried runs of epoxy have been sanded off of frame #1 and gussets. This is the starboard side.

Starboard frame #1 after sanding. The seat riser cutouts still need to be encapsulated with epoxy.

Port frame #1 after sanding.

Port frame #1 after sanding.

Port frame #1 after sanding.

The globs of epoxy are now sanded off of the transom.

Read More..

Sabtu, 10 September 2016

More Uses for a Two ton Crane

My neighbor at the shop came up with yet another novel way to use the two ton overhead crane.


Ben floating over the bottom of his boat with his dad in the background steering the crane to move him into position for applying the next batch of resin.


Read More..

Rabu, 24 Agustus 2016

Preparing the stem for encapsulation

I should have encapsulated the stem a long time ago, before I ever attached it to the keel. Im not sure why I didnt. Nonetheless, I did not. I wont repeat that mistake on the Zip.

In any case, it needs to be done now before the planking goes on. In preparation for encapsulating the stem, I need to sand away several dried globs of epoxy that have been stuck on it since earlier stages in construction. The worst of these are directly behind the chines, where they are attached to the stem.

I worked on that a little earlier this morning. As this is the middle of the week, and free time is quite limited, Im expecting several more days of small, incremental progress in this task.
Read More..

Selasa, 28 Juni 2016

Shim for the strongback

shim for deck framing strongback

As it turns out, I did install the strongback incorrectly.

Even after Id faired the front of the breasthook down to meet the sheers, it was readily apparent that the forward angle on the strongback was too steep. What I should have done was to notch the bottom of the strongback, so that the front of it extended several inches across the top of the breasthook.

Instead, I cut the whole thing too short, and bent it down too far. 

Cant change that now.

So, I made a shim from a 16" piece of Southern Yellow Pine. Using a block plane and my planer/jointer, I formed it to fit into place. Then I epoxied it on. 

The next step will be to sand the top of it down so that the deck will fit properly.


My test piece of plywood clearly shows that the angle of the strongback is too steep.


The shim, clamped into place while the epoxy cures.



Read More..

Kamis, 09 Juni 2016

Drilled for the Bow Eye

My bow eye came in from Glen-L earlier this week. I went with a 3/8" single-post, stainless steel cast type rather than the U-bolt type... I only wanted to drill one hole.

To prep the bow of the boat for drilling, I located & marked the spot where I wanted the bow eye to go... in-between the planking screws on either side.

I ground away the fiberglass in a small spot with my Dremel, and then slowly & cautiously began drilling with a very small drill bit. I used the vertical line of the bow as a reference for trying to keep the drill bit parallel with the center of the stem.

Bit by bit, (literally), I expanded the hole with increasingly larger diameter drill bits, until I finished the hole with 12-inch long 1/4", 5/16" and 3/8" bits.

Did I drill the hole dead-center all the way through?

No. Of course, not. 

However, itll work. Once the boat is flipped, I can re-enforce the "thin" side of the stem if I feel its warranted.

Soon, I should be back to painting.

Happy Fathers Day!



The Hello Kitty make-up mirror that I lifted from my daughter has been invaluable at things like getting this shot of the inside of the stem. As you can see, the exit hole is off-center... but itll work.

Read More..

Minggu, 14 Juni 2015

Fishing boat kits for sale Details

Foto Results Fishing boat kits for sale Remote Control RC Boat Sale Party Hut Pontoon Boats for Sale Wooden Model Boat Kits for Sale , Wooden Pirate Boat Models, Fishing Sail Boat Kits for Sale in UK Triton Center Console Boats for Sale
Read More..

Kamis, 11 Juni 2015

Plans for building an ice boat

Plans for building an ice boat Free catamaran plans to build your own boat - all homemade, Free catamaran plans to build your own boat use our free catamaran plans to build a stable sailing boat at half the cost. this wooden catamaran has a simple design is Floating dock | floating dock plans | boat dock, This is the floating dock you would own if you
Read More..

Rabu, 10 Juni 2015

Plans for building a boat dock

Plans for building a boat dock Dock plans - boat docks, Dock plans. these free plans for wood dock sections are ideal for residential or light commercial application. we have all the hardware you need to build it right the How to build a floating dock - life123, Knowing how to build a boat dock is essential if you want to maximize your waterfront
Read More..

Minggu, 31 Mei 2015

More Model boat kits for sale uk

Topic Model boat kits for sale uk Hi, this time i Know and you can take a benefit from here guide for Model boat kits for sale uk from another source Car and truck model kits for sale at jimnohio., Builder: steve m. from kentucky: automotive model kits (and a few planes and armor) we ship worldwidepricing lower on page!. Boats for sale - buy & sell, new & used boats ,
Read More..

Stitch glue for fabric

Stitch glue for fabric Cross Stitch On Fabric Craft Glue (macam-macam lem untuk craft-ku) Liquid Stitch Fabric Glue Strong Fabric Glue How to Make Fabric Frames
Read More..

Kamis, 28 Mei 2015

Drift boat plans for sale

Drift boat plans for sale Tri-Hull Boat Plans Free Plans Dory Drift Boat Wooden Ski Boat Drift Boat Plans Kits Drift Boat Plans
Read More..

Selasa, 26 Mei 2015

This is Free plans for boat building

guide Free plans for boat building meet here this time i have experience and you can take a benefit from here guide for Free plans for boat building from another source Links:free- boat - plans [tdem], Here are links to all the free boat plans i could find on the internet. also be sure to check out my one sheet boat links as most of them are free plans.. Free
Read More..

Kamis, 21 Mei 2015

Plans for building a boat lift Details

Foto Results Plans for building a boat lift Tunnel Hull Boat Plans Luxury Yacht Interior Design Lake Ray Hubbard Rockwall TX DIY Boat Lift for Garage Pocket Cruiser Sailboats
Read More..

Rabu, 20 Mei 2015

Riva boat plans for sale

Riva boat plans for sale Classic wooden boat plans � minimax 8, Baby bootlegger. this iconic racing boat was originally designed by george crouch in 1924 and went on to win the 1924 and 1925 apba gold cup. our plans for this boat Classic wooden boat plans � deep v 16 inboard, Baby bootlegger. this iconic racing boat was originally designed by george
Read More..

Jumat, 15 Mei 2015

Layout boat plans for sale

Layout boat plans for sale RC Model Boat Plans Free River Drift Boat Plans Check layout boats for sale Best relationship between clinker and Jon Boat Deck Layout Plans Dn Ice Boat For Sale Plans building wood boats free plans
Read More..

Senin, 11 Mei 2015

Porsche design boat for sale

Porsche design boat for sale Wally Power 118 Yacht Catamaran Yacht Designs Porsche Design RFF135 Yacht Audi Speed Boat Div Div Class
Read More..

Rabu, 06 Mei 2015

Boat design for dummies

Boat design for dummies CPR for Dummies | Design News From All Over The World Folding Boat Plans ?????: Scott Burdick Chain Watch Earrings Wind Up Alarm Clocks
Read More..

Senin, 04 Mei 2015

Boat design for cake

Boat design for cake Hull speed - boat design forums, Hull speed notes on hull speed and the gross misconceptions surrounding it. these notes concern displacement craft. i did a fast search in google for boat �hull Parmesan-crusted crab cake bites and a winner! | home is, I'm always hoping to reel in some quick and easy recipes for the holiday season, so
Read More..